How to Replace a Kia Sportage Replacement Key

The key of a lot of kia key fob replacement cost (simply click the next document) models has a keyless entry system built into. The key functions like the remote control, and is exchangeable by an Kia dealer.

Key fobs might stop working for a variety of reasons, such as an empty coin battery, worn buttons water damage, signal interference and a damaged receiver module. Here are some suggestions to help you get your kia picanto key fob programming sportage replacement key to work for good.

How to replace the remote key or smartkey

If your Kia is equipped with an intelligent key, remote key push to start key, or a regular non-transponder steel key The battery inside these keys will eventually need replacement key kia. This is particularly when your car shows a message that states the remote or smart keys are in poor condition.

It's a fairly simple procedure. In order to replace the battery in the key fob take out the mechanical key from the slit on the back of the key fob and break the cover. A small screw will be in the key fob to keep the battery in place. Utilizing a small screwdriver remove the screw and remove the old battery. Then, you can insert the new battery and close the slit on the key fob.

Once the key fob has a fresh battery and you've tested it, press the locks and unlock buttons. If the doors unlock and lock exactly as you expect, then you're all set! You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers start to get cold or you have to do some errands in Brandon.

Note: Some key fobs (transponder chip or smart keys) might require their programming completed. This requires a specific programming machine that only the dealer or locksmith can access. Other keys (non transponder metal keys), do not need programming. If your key needs to be programmed, you must be aware of the number stamped on the tag that identifies the key and keep it in a safe place.

How do you replace a dead battery?

If your Kia key fob isn't responding to pressing the lock or unlock button on the fob, it is a good indicator that the battery needs to be replaced. A low battery may also cause other issues such as the check engine light coming on or delayed cranking of the engine. Fortunately replacing the battery on the key fob is a fairly simple DIY project that requires only the most basic tools.

Be sure to turn off your vehicle and shut all doors prior to starting. Find the small metal or a plastic piece at the bottom of the key fob. Move it until the key falls out. Then, you can insert the key into the handle of the door for the driver to open your car.

To replace the battery on the key fob remove the rear cover. Use a pry tool to remove the latch that holds the black negative cable. Remove the old battery and then align the replacement battery to ensure its "+" side is facing you and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid damaging or bending the contacts of the metal.

Once the new battery has been installed and the key fob is turned on, turn it off and on in the ignition repeatedly until the door locks. You can then test the Kia's Key fob to ensure it's working properly.

How do you replace the smart key

Depending on the model of your Kia Sportage, you may have a standard key fob or a smart key. The smart key kia sportage key has an embedded mechanical key blade, unlike the standard key fob, which does not. Both kinds of key fobs come with batteries that will eventually have to be replaced. This is a simple procedure which takes just two minutes.

Before you start, you will want to ensure that you're on a level surface with good lighting and that your Kia is off. Remember that the fob contains small pieces that could fall when you're not careful.

The first step is to find the small release button on the backside of the fob. It could be a circular silver button or a rectangular slot. Once you press this the mechanical key blade will come out and you can then open the key fob.

After the key fob has been open, remove the battery that was in it. The new battery is a the CR-2032, and it can be bought online or in your local auto parts store. When you're done, the key fob should be able to lock the vehicle, unlock it, and then start your vehicle, even if it isn't running.

How to replace the mechanical key

The Kia key fob is a fantastic feature that lets us lock and unlock our vehicle with the click of one button. But, as with all devices, it can have problems occasionally. Luckily, there are steps that can be taken to solve these issues and ensure that our key fobs are in good condition for the long term.

One of the most common issues is a low or dead battery. This can cause your fob to stop working or work intermittently. If this is the case then replace the battery with a new one.

If this doesn't fix the problem Try using a standard flat-head screwdriver to break open the fob's plastic casing. Be careful not to harm any internal components or scratch the plastic. After the battery has been removed and replaced, you can replace it with a brand new one.

Close and open the door using the mechanical key. (Every Kia fob comes with a spare mechanical key that fits into the slot). Test the fob to make sure it's working properly. If the key fob isn't working, call a dealer or locksmith to help resolve the problem. Make sure they make you an emergency key that can work in all the door and trunk cylinders to prevent lockouts in the future.