Replace Nissan Key Fob Batteries

If your Nissan key fob isn't responding to your commands, it's likely that its battery is dying. It's an easy fix that most people can fix themselves.

To change the battery, you can either purchase an alternative one from a hardware store or consult the owner's guide for the model you own.

Removing the Battery

The key fob that you have in your nissan qashqai spare key model comes with a built-in battery that can eventually lose its charge. The battery in the key fob can be replaced within a matter of minutes. You'll first need the CR2032 battery. This is a small coin cell battery that is often used in key fobs and can be found in most convenience stores. You'll also require gloves (latex or non-latex) and an affixed screwdriver that is small enough to open the fob. Read the owner's manual for specific instructions and steps before you begin.

Once you have the new battery, take off the old one by turning the fob upside down and looking at the back side. There will be a small latch that you need to open by pulling down. This will release the mechanical key from its original position inside the fob.

Then, insert the brand new battery, and make sure that it's positioned correctly. Close the fob after the battery is in place and then click the two sides of the fob together. After completing this final step make sure to test your key fob by pressing the unlock button, and then seeing what happens. You'll be able to use the numerous features of your Nissan to determine if everything is working properly. After changing the battery, it's a good idea to reset your key fob to make sure that it's working correctly.

Replace the Transmitter

With your key fob functioning as the "key" to so many of your car's essential functions, it could be a major blow in the event that you lose or damage it. A damaged or broken key fob will stop you from locking or starting your car.

It's a good idea to keep a spare keyfob at to hand in the event of an emergency. Fortunately, the process for replacing your nissan replacement key Fob key fob is simple. You'll require a new battery and a small flathead screwdriver to get rid of the old one However, the process of replacing it is a breeze and should only take just a few minutes.

You'll need a round Panasonic CR 2032 3V battery (you are likely to find them in multipacks for less than $5 USD). The battery is located in the back of the key fob. You'll require a small flathead screwdriver in order to gently break the two halves. Use a flathead screwdriver and a small flathead to take off the clip that is on the top of the battery. Make sure to note the location. Replace the battery, then assemble the key fob. Check it out to confirm it is working.

Nissan Intelligent Keys will eventually wear out and require to be changed, just like any other electronic device. Guard your key fob from water, magnetic fields and physical impacts. Do not drop it or apply too much pressure to the device.

Replacing the Key

When your Nissan key fob is dead you won't be able to use it to unlock or start your car. This is a problem for those who have to go to work in Detroit or go on errands around Dearborn.

It's not hard to change the battery in your Nissan Smart Key. You can do it at home or at the dealership and usually, you can locate a pack for less than $5 at an hardware store.

Start by flipping the fob on its side and pushing a small latch on the back. This will release the emergency mechanical keys inside. Although you won't be able to use the emergency key to start your vehicle but it will allow you to open the door.

Next, look for a small cut on the top of the casing for the key fob. You can make use of a screwdriver to pull off the two pieces of the key fob. Once you have access to the battery inside, pull it out and make note of the position it is in. When you're ready to put back together the key fob, slide the new battery into its spot and secure the two components of the case. Insert the mechanical key and your Nissan smartkey will work just as normal.

Other Problems

A lot of modern cars have key fobs, which let you to lock them and open them without having a physical key. Key fobs use a transmitter to connect to the computer system of the car.

There are several possible reasons that your Nissan key fob won't work after replacing the battery. For instance, the new battery might not be properly seated within the key fob. Another possibility is that the key fob has to be reset. It's an easy task that can be completed at home with a few simple tools.

You'll need, for example an screwdriver with a flat-headed tip to take out the battery that was in the key fob. Then, using a screwdriver, pull the back of the keyfob open and insert the new batteries. Finally, you'll need to change the programming of the key fob to ensure it works with your vehicle.

Fortunately, the majority of Nissan key fobs are programmed by the user which means you can accomplish this yourself. This is usually done by inserting the fob into the ignition two times within five seconds. If this does not work, take your key fob in to a dealer or auto locksmith to have it programmed. The cost will depend on the person you speak to and type of vehicle you own.